banjalukaforum.com
https://www.banjalukaforum.com/

Debian 4.0 Etch - Stable verzija
https://www.banjalukaforum.com/viewtopic.php?f=16&t=27753		 Stranica 1 od 2
Autoru:  che.guevara [ 08 Apr 2007, 22:14 ]
Tema posta:  Debian 4.0 Etch - Stable verzija
Konačno je izdata stabilna verzija najbolje linuks distribucije - Debian GNU/Linux. Distribucija se nalazi na mnogim mirrorima i to kao CD odnosno DVD izdanje. Inače važan je samo prvi CD odnosno DVD, sve ostalo je opcionalno.

Moje preporuke.

Debian vaskrse, vaistinu vaskrse!

http://www.debian.org
Autoru:  dsimic [ 10 Apr 2007, 13:04 ]
Tema posta: 
Pustio sam download, bice gotovo najvjerovatnije sutra poslijepodne, i386 i amd64...
Eto, kome treba, neka se javi na PM... ;)
Autoru:  che.guevara [ 10 Apr 2007, 17:03 ]
Tema posta: 
dsimic je napisao:
Pustio sam download, bice gotovo najvjerovatnije sutra poslijepodne, i386 i amd64...
Eto, kome treba, neka se javi na PM... ;)


Poslije ponedeljka biće i na "lokalnom" distro shopu. Poz svima. Odoh da ga instaliram.
Autoru:  che.guevara [ 11 Apr 2007, 10:12 ]
Tema posta: 
Ради ко змај :)))

Имам неких ситних проблема са хардвером, наравно то никако не могу да замјерим дистрибуцији ;)
Autoru:  kiovva [ 11 Apr 2007, 11:24 ]
Tema posta: 
che.guevara je napisao:
Ради ко змај :)))

Имам неких ситних проблема са хардвером, наравно то никако не могу да замјерим дистрибуцији ;)


Ова четворка се појавила сувише брзо за Debian. Шта не ваља? :Р

Ај' баци мало утисака, важи?
Autoru:  che.guevara [ 11 Apr 2007, 11:41 ]
Tema posta: 
Pa valja recimo zvuk, valja multimedija (meni su svi filmovi kodirani sa mencoderom, lavc format), ukljuceni ati drajveri rade odlicno (doduse bez 3d akceleracije), radi hibernate bez problema, synapric je i dalje brz k'o zmaj...

FireFox su preimenovali u IceWeasel posto su imali nekih sporova sa mozillom :) Dakle isti browser, isto sve, samo ime drugacije i nema vise sporenja :D

Java me malo zeza, mislim ne znam zasto nisu stavili jdk na prvi DVD kad je sad java GPL-ovana :/ Opet guraju kaffe(ine?) i gnujava, mada je Sun Java bolja, ipak racunam da se to nalazi na drugom DVD-u kojeg jos nisam isprobao.

E da, compiz dolazi uz sistem, samo ga "malo" treba podesiti da bi proradio (pri tom treba instalirati i drajvere za graficku, koji obicno nisu open/free, osim za Intel kartice). GNOME naravno shljaka a po defaultu tu je i neki lightweight manager (fvwm?). KDE je takodje podrzan i nalazi se na prvom DVD-u. Eto tako :)

Btw izgleda da mi ne radi mikrofon :P Bezze. To moram da sredim :)

Ethernet je prepoznao dobro i na njega nemam zamjerki a wireless nisam jos testirao.

Toliko za sad :)
Autoru:  altoid [ 17 Apr 2007, 19:12 ]
Tema posta: 
Etch koristim vec neko vrijeme, i i dalje mi je Debian omiljeni distro za servere. :)

A sad treba dist-upgrade na Lenny na jedno 7 masina.....
Autoru:  filozof sa vrbasa [ 11 Jun 2007, 13:37 ]
Tema posta: 
Kako se Debian snalazi sa winmodemima! Javite molim vas!
Autoru:  Пеле Мали [ 11 Jun 2007, 18:34 ]
Tema posta: 
kao i svaki drugo distro ..
za winmodeme imas drivere , instaliras i picis :)
Autoru:  che.guevara [ 11 Jun 2007, 23:04 ]
Tema posta: 
filozof sa vrbasa je napisao:
Kako se Debian snalazi sa winmodemima! Javite molim vas!


Ako planiras da surfas sa modemom, kupi ili pozajmi neki hardverski komad i sacuvaj svoje dragocijene zivce!
Autoru:  Пеле Мали [ 12 Jun 2007, 10:06 ]
Tema posta: 
@filozof sa vrbasa

koji winmodem imas? ja sam imao Conexant HSF i uopste nije bio neki problem podesiti net..
Autoru:  filozof sa vrbasa [ 12 Jun 2007, 11:20 ]
Tema posta: 
Smart Link , i nasao sam driver za njega, ali ni jedan nije za moju verziju Linux 2.6.19 , stvarno ne znam vise sta da radim i kako!
Autoru:  Пеле Мали [ 12 Jun 2007, 12:03 ]
Tema posta: 
filozof sa vrbasa je napisao:
Smart Link , i nasao sam driver za njega, ali ni jedan nije za moju verziju Linux 2.6.19 , stvarno ne znam vise sta da radim i kako!


hm, evo proguglao sam malo pa sam ti nasao ovo:
http://linmodems.technion.ac.il/packages/smartlink/

koliko sam skuzio, potrebno je instalirati najnoviju verziju drivera i vidim ima patch za 2.6.19, tj. tvoju verziju kernela (slmodem-last-2.6.19.1.patch.gz )

p.s.
mozda bi trebao otvoriti novu temu za ovo :)
Autoru:  filozof sa vrbasa [ 12 Jun 2007, 12:37 ]
Tema posta: 
Druze kad sam skinuo taj fajl unutra je bio jedan fajl manji od 1 kb i nije mi jasno sta trbad da radim sa njim nije se mogao instalirati, a nisam znao gdje ga ubaciti, iskopirati!

PCIDEV=2000:2800
CLASS="Class 0703: 2000:2800"
NAME="Modem: Smart Link Ltd. Unknown device 2800 "
Vendor=2000
Device=2800
SUBSYS=1801:2800
SUBNAME=" Unknown device 1801:2800"
SUBven=1801
IRQ=5
Test="./scanModem test 2000:2800 1801:2800"
IDENT=slamr
TST=

Smart Link


Smartlink modem setup.
-----------------------------------------------------------
The modem should setup with:
modprobe ungrab-winmodem
modprobe slamr
slmodemd -c YOUR_COUNTRY /dev/slamr0
which should announce creation of ports:
/dev/ttySL0 --> /dev/pts/N , N some number
Specify the symbolic link /dev/ttySL0 as the port to be used by dailer software.


SmartLink (http://www.smlink.com/) chipset modems are sold under a variety
of BrandNames, and have vendor IDs 163c, 2000, 2003, and 2004. Conexant bought
Smartlinks's modem techhology sector in 2005. While Linux updates are not
expected from Conexant, Linux support is still very good thanks to volunteer
Linux maintainer Sasha Khapyorsky. Get his updated software from:
http://linmodems.technion.il/packages/smartlink/

A high level support component is a smart helper: slmodemd
Acting through one of several drivers, it creats ports dynamically and
supports COMM and FAXing functions. During facsimile usage, the AT&F command
is not supported. A means of implmenting the CNG is lacking, because this
function is encoded within the dsplibs.o precompiled at Smartlink, Inc. See
http://marc.theaimsgroup.com/?t=116026350800001&r=1&w=2
http://marc.theaimsgroup.com/?l=hylafax ... 404444&w=2
Usage of SMP (Symmetric MultiProcessor) mother boards is
supported. For service on 64 bit AMD x86_64 processor mother boards, see
http://linmodems.technion.ac.il/archive ... 02594.html
http://linmodems.technion.ac.il/archive ... 02490.html
However a 64 bit compilation of a proprietary dsplibs.o conponent is not
available. Hence for modem usage the computers must be operated in 32 bit mode.

The slmodemd supports a few different types of modem drivers. Below the suffix
.ko means the modular form of a driver, before loading into the kernel. The
slmodemd does not access the modem hardware directly. Rather access is provided
through lower sophistication drivers. Prior to usage of a slamr driver, there
must be a release of serial driver interference by loading of: ungrab-winmodem.ko
For PCI card modems with Smartlink chips the driver used is: slamr.ko
For USB modems with ID 0483:7554 use Smartlink driver: slusb.ko
For ALSA (Advanced Linux Sound Architecture) modem drivers, see the Table below.

Sasha's core resources are:
----------------------------
ungrab-winmodem.tar.gz - for compiling a ungrab-winmodem.ko driver
slmodem-2.9.11-MostRecentDate.tar.gz - the core code resource for compiling
and installing slmodemd, slamr.ko and slusb.ko. The slmodemd dynamically
creates ports and provides higher level COMM functions, after driver
loading. Not being a driver, slmodemd serves under alternative boot kernels.
ALSA modem drivers, included with 2.6.n kernel+module releases.

Some derivative resources at http://linmodems.technion.il/packages/smartlink/
SLMODEMD-1.0.13.tar.gz - containing a compiled slmodemd and usage instructions.
When used with ALSA modem drivers, further compiling is not necessary.
> SLMODEMD-1.0.13.tar.gz will suffice for getting online, though read on about automation. <<< See Compiling_slmodemd below, for details.
sl-modem-daemon-SomeVersion.deb - an installer for Debian related distros.
It has slmodemd and scripts for starting slmodemd at boot.
This package is also available from repositories of Debian related distros
Ubuntu, Kbuntu, Ebuntu, Xandros, Kanotix and others.
sl-modem-daemon-SomeVersion.tar.gz has the same contents, but is repackaged
in an easily opened format, for access to its automation scripts.
After unpacking, they are resident in the etc/ subfolder
sl-modem-source-SomeVersion.deb - is a Debian installer for the slamr and slusb
source code. It is Not necessary for ALSA driver usage.
slamr-KernelVersion.tar.gz - for several Ubuntu KernelVersions, containing:
ungrab-winmodem.ko, slamr.ko, slusb.ko, slmomdem, setup script and as
a convenience, the sl-modem-daemon-SomeVersion.deb. Look in the folder:
http://linmodems.technion.il/packages/smartlink/ubuntu/

Slmodemd actions
-----------------------------------------
Start working with slmodemd with commands:
slmodemd --help
slmodemd --countrylist
The long output can be written to a Clist.txt file with:
slmodemd --countrylist &> Clist.txt
Find your COUNTRY_NAME within the 2nd column if the list and record it.
It will be used in capital letters during the modem setup command.
Try USA if your COUNTRY is not in the list.

Before modem setup root/adm capacity must be acquired with:
su - root
or by prefixing commands with "sudo" for Ubuntu Linux and its cousins.
The setup command is:
slmodemd -c COUNTRY_NAME --alsa slmodemd_device
if successful there will be reported dynamic creation of:
/dev/ttySL0 --> /dev/pts/N , with N a number
The /dev/ttySL0 is a symbolic link to the real modem port /dev/pts/N ,
and it is /dev/ttySL0 which should be named to dialup utilities such
as wvdial. The "--alsa" is only needed for usage with ALSA modem drivers.
Throughout a dialout session slmodemd MUST be kept running. Open another
console/termimal to startup dialout software such as wvdial.

The slmodemd device nodes
---------------------------
The slmodemd_device is different for the several modem drivers.
For usage with slamr.ko , the slmodemd_device is /dev/slamr0 , within
the command sequence:
modprobe ungrab-windmodem
modprobe slamr
slmodemd -c COUNTRY_NAME /dev/slamr0
For USB modem usage:
modprobe slusb
slmodemd -c COUNTRY_NAME /dev/slusb0
For a modems using a ALSA driver, details are below.

The /dev/slamr0 and /dev/slusb0 will be made the slmodem installation
processes. However, they usually will NOT survice reboot, because
most current Linux have ports created in volatile RAM space. However
the these devices can be manually created under root/adm persmission with:
mknod -m 600 /dev/slamr0 c 242 0
mknod -m 600 /dev/slusb0 c 243 0
if automation scripts are not yet in place.

For automation of RPM using Linux distros see:
http://www20.brinkster.com/olivares/slm ... tup-1.html
For any Distro the following lines will serve in /etc/modprobe.conf or subfolders of
/etc/modprobe.d/:
--------------
alias char-major-243 slusb
alias char-major-242 slamr

# The following install and remove commands are to be written as single lines.
# Preloads ungrab-winmodem and creates a device node upon "modprobe slamr"
install slamr modprobe --ignore-install ungrab-winmodem ; modprobe --ignore-install slamr; test -e /dev/slamr0 || (/bin/mknod -m 660 /dev/slamr0 c 242 0 2>/dev/null && chgrp dialout /dev/slamr0)
# rpm using distros should use "uucp" rather than "dialout"

# Removes slamr and ungrab-winmodem successively:
remove slamr /sbin/modprobe -r --ignore-remove slamr ; /sbin/modprobe -r --ignore-remove ungrab-winmodem

# creates /dev/slusb uponn slusb driver loading.
install slusb modprobe --ignore-install slusb ; test -e /dev/slusb0 || (/bin/mknod -m 660 /dev/slusb0 c 243 0 2>/dev/null && chgrp dialout /dev/slusb0)
# rpm using distros should use "uucp" rather than "dialout"



Usage with ALSA modem drivers
--------------------------------
See SoftModem.txt for a description of the hardware. For a modem using
an ALSA driver, the slmodemd_device only has to be specified within the
slmodemd command line. A preliminary "mknod something" command is not necessary.
The Table shows hardware PCI ID, its card type, driver and slmodemd_device name.
The ALI5451 and HDA (High Definition Audio) cards can host softmodems. For these
cards hw:0,0 is the audio card designation and the modem Subsystem on it
is most commonly hw:0,1 , but there are some hw:0,6 cases. For the older
soft modem controller family, the ALSA software first assigns hw:0 to an audio
card, and the following modem designation is hw:1 or equivalently modem:1
An attempt to use modem:0 may initially appear successful, but modem:0 or hw:0
is actually the companion audio card.

PCI ID controller ALSA driver slmodemd_device
========= =============== =============== ===================
several HDA cards snd-hda-intel hw:0,1 or hw:0,6
10b9:5451 ALI5451 audio snd-ali5451 hw:0,1
------------------ softmodem controllers --------------------------
1002:434d ATI snd-atiixp-modem modem:1
1002:4378 ATI " "
1106:3068 VIA snd-via82xxx-modem "
8086:xxxx many Intel snd-intel8x0m "
10de:00d9 Nvidia Corp " "
SIS 630 " "
Others? " test "
---------------------------------------------------------------------------
* The scanModem script tries to determine ALSA modem driver and slmodemd_device
dynamically from /proc/asound/ information, or the internal Archive as a fallback.

Do a precautionary unloading and reloading of the driver.
su - root (not for Ubuntu)
modprobe -r driver
modprobe driver
This precaution is sometimes necessary, because a driver may functionally die
although loaded. But usually it can be skipped.
For this System, scanModem deduced slmodemd_device is:
For most modems the setup command is:
slmodemd -c COUNTRY_NAME --alsa modem:1
For modems on HDA cards, the command is:
slmodemd -c COUNTRY_NAME --alsa hw:0,1
though there have been cases of hw:0,6
For the ALI5451 hosted modems, a shortbuffer (-s) option is needed:
slmodemd -s -c COUNTRY_NAME --alsa hw:0,1


The slamr diagnostic
---------------------
Sasha has provided slamr.ko with a capability for reporting softmodem codecs,
even for modems not supported fully by slamr. This is useful when other
resources do not report out the modem codec, needed to distinguish between
hsfmodem, slamr and ALSA driver support alternatives.
This slamr test is Not effective for softmodems on HDA audio cards.

The test routine is:
modprobe ungrab-winmodem
modprobe slamr
followed by a readout from the dmesg buffer with:
dmesg | grep slamr
Among the few output lines, there is one like:
slamr: mc97 codec is SIL27
reporting in this example an ALSA driver supported, Agere Systems codec SIL27.
Conexant codecs have format CXTnm, nm a number. These modems are not ALSA driver supported.
Softmodems with all other codecs should be ALSA driver plus slmodemd supported.

YourSystem

his file should NOT be sent to Discuss@Linmodems.org
It has common guidance for modem usage after setup.

Debian is not yet providing pre-compiled drivers for WinModems

The Modem/DriverCompiling.txt is a MUST READ,
if you are not experienced in configuring kernel-source/
or get "unresolved symbols" upon driver insertion.

Most recent WinModem fixes are in: http://linmodems.technion.ac.il/FAQ.html

(4) For guidance on automation see http://linmodems.technion.ac.il/archive ... 03734.html
and the scripts in the slmodem-2.9.n/scripts folder/

Modem Data

Only plain text email is forwarded by the DISCUSS@linmodems.org List Server.
Do use the following as the email Subject Line:
SomeName, YourCountry Debian GNU/Linux 4.0 kernel 2.6.19
This will alert cogent experts, and distinguish cases in the Archives.
YourCountry will enable Country Code guidance.
Occassionally responses are blocked by an Internet Provider mail filters.
So in a day, also check the Archived responses at http://www.linmodems.org .
Local Linux experts can be found through: http://www.linux.org/groups/index.html
-------------------------- System information ----------------------------
CPU=i686, Debian GNU/Linux 4.0
Linux version 2.6.19 (root@Knoppix) (gcc version 4.1.2 20061028 (prerelease) (Debian 4.1.1-19)) #7 SMP PREEMPT Sun Dec 17 22:01:07 CET 2006
scanModem update of: 2007_May_11


ALSAversion 1.0.13
USB modem not detected by lsusb

Modem or host audio card candidates have firmware information:

PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:0b.0 2000:2800 1801:2800 Modem: Smart Link Ltd. Unknown device 2800

Modem interrupt assignment and sharing:
5: 21119 XT-PIC-XT VIA686A

--- Bootup diagnositcs for card in PCI slot 00:0b.0 ----
PCI: Found IRQ 5 for device 0000:00:0b.0
PCI: Sharing IRQ 5 with 0000:00:0b.0

=== Finished modem firmware and bootup diagnostics section. ===
=== Next deducing cogent software ===

For candidate modem in PCI bus: 00:0b.0
Class 0703: 2000:2800 Modem: Smart Link Ltd. Unknown device 2800
Primary PCI_id 2000:2800
Support type needed or chipset: slamr


The modem is supported by the Smartlink slamr driver
plus the slmodemd helper utility. Read the
Smartlink.txt and Modem/YourSystem.txt for follow through guidance.

Writing Smartlink.txt
============ end Smartlink section =====================

Completed candidate modem analyses.

The base of the UDEV device file system is: /dev/.udev

Versions adequately match for the compiler installed: 4.1.2
and the compiler used in kernel assembly: 4.1.2

Kernel-header resources needed for compiling are not manifestly ready!

If compiling is necessary packages must be installed, providing:
kernel-source-2.6.19
Compressed files at: /usr/src/linux-2.6.19.tar.bz2 /usr/src/loop-aes.tar.bz2 /usr/src/madwifi.tar.bz2 /usr/src/ndiswrapper-source.tar.bz2 /usr/src/patch-2.6.19.1.bz2 /usr/src/rtai-source.tar.bz2

For Debian and some related distributions, a package kernel-kbuild-2.6-3 may be needed to support driver compiling


Checking pppd properties:
-rwsr-xr-- 1 root dip 260920 Nov 14 2006 /usr/sbin/pppd

In case of an "error 17" "serial loopback" problem, see:
http://phep2.technion.ac.il/linmodems/a ... 02637.html

To enable dialout without Root permission do:
$ su - root (not for Ubuntu)
chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
chmod a+x /usr/sbin/pppd

Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
noipdefault
passive
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx

In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch ... 04656.html


Don't worry about the following, it is for the experts
should trouble shooting be necessary.
==========================================================

Checking for modem support lines:
--------------------------------------
/device/modem symbolic link:
slmodemd created symbolic link /dev/ttySL0:
Within /etc/udev/ files:

Within /etc/modprobe.conf files:
/etc/modprobe.d/alsa-base-blacklist:# Uncomment these entries in order to blacklist unwanted modem drivers
/etc/modprobe.d/alsa-base-blacklist:# blacklist snd-atiixp-modem
/etc/modprobe.d/alsa-base-blacklist:# blacklist snd-via82xx-modem
/etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2
Within any ancient /etc/devfs files:

Within ancient kernel 2.4.n /etc/module.conf files:
/etc/modules.conf:options snd-atiixp-modem index=-2
/etc/modules.conf:options snd-via82xx-modem index=-2
/etc/modules.conf:# Uncomment these entries in order to blacklist unwanted modem drivers
/etc/modules.conf:# alias snd-atiixp-modem off
/etc/modules.conf:# alias snd-via82xx-modem off
--------- end modem support lines --------

I ovo je sve iz modemScan! Hvala!
Autoru:  Пеле Мали [ 12 Jun 2007, 18:05 ]
Tema posta: 
hm, evo ovako da krenemo ispocetka..
skinuo sam ovaj fajl:
http://linmodems.technion.ac.il/package ... 505.tar.gz

u README stoji:
Kod:
Requirements
============

CPU: Intel Pentium II, Celron. AMD K6, Cyrix 500MHz or higher.
Memory: 64MB.

OS: Linux 2.4. You need the kernel header files at least (or full kernel
               source tree) installed and configured.
[b]    Linux 2.6. You need the full kernel source tree installed and configured.
[/b]


znaci to imas .. (provjeri jedino jel ti kernel source instaliran)

dalje u README imas opisanu instalaciju.

a sto se tice ovog fajla, sto sam ti dao kao patch (http://linmodems.technion.ac.il/package ... 1.patch.gz)
dakle, njega raspakuj i taj fajl koji dobijes kopiras u direktorij patches/ , koji ces dobiti kad raspakujes driver i tek onda pokreni instalaciju.
mislim da je to postupak ..
Autoru:  filozof sa vrbasa [ 12 Jun 2007, 23:18 ]
Tema posta: 
E pokušaću pa ću ti javiti! A kernel valjda imam, na usr/src/ linux.2.6.19 tu sam vidio gomilu file~
Autoru:  filozof sa vrbasa [ 14 Jun 2007, 16:18 ]
Tema posta: 
Napravio sam modem i surfam brzinom od 25 kb/s! Hvala svima koji su mi pomogli! :D
Autoru:  che.guevara [ 14 Jun 2007, 16:37 ]
Tema posta: 
filozof sa vrbasa je napisao:
Napravio sam modem i surfam brzinom od 25 kb/s! Hvala svima koji su mi pomogli! :D

Svaka ti cast! Nisam vjerovao u tebe, ali srecom pogrijesio sam :) Brzina ti je na pola koplja vjerovatno zbog djeljenja linije.
Autoru:  filozof sa vrbasa [ 14 Jun 2007, 20:04 ]
Tema posta: 
Hvala, nisam ni ja vjerovao, moj sljedeći post je trbao biti tipa , "Da li je u redu surfati iz Win, a onako sastrane i po potrebi korisiti Linux?" Međutim nije bilo potrebe i uštedio sam kao što si rekao živce i nekoliko desetina maraka! Sad bih trbao savjet , šta od zaštite uključiti u Linuxu i kako, pošto sam čuo da Linux nema nekih opasnih virusa i da se mogu izbrojati na prste jedne ruke! A djeljenje linije, šta pod tim podrazumjevaš?
Autoru:  che.guevara [ 15 Jun 2007, 17:10 ]
Tema posta: 
Pod dijeljenjem linije podrazumijevam da si dvojnik sa nekim i da zbog toga možeš da ostvariš samo pola dialup protoka a ADSL nije ni moguć.

Od antivirusa i firewall'ova - ne treba ti ništa. Ne skidaj ništa sumnjivo već samo slobodan softver i siguran si 99%.
Stranica 1 od 2 Sva vremena su u UTC [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/